Getting Familiar with Plumbing: Your Starting Point for When Installing a Bathtub
Getting Familiar with Plumbing: Your Starting Point for When Installing a Bathtub
Blog Article
The article down below about A Step-by-Step Guide to Installing a Bathtub is quite stimulating. You should check it out.
Mounting a bath tub isn't precisely brain surgery, yet it does need solid plumbing, carpentry, and occasionally, tiling skills. Replacing an old bathtub with a brand-new one is likewise a moderately tough project. If the old bathtub is readily easily accessible, the task can relocate speedily; if you need to open a wall to get rid of the old tub as well as place the new bath tub, the task is much harder. In either case, the job is within a house handyman's abilities, although you will certainly need a helper to move out the old bathtub and also embeded in the new one. Make certain you have actually certified yourself for the job and also are comfortable trying it. Instead of working with a service provider to take over a halfway-completed task, it is much better to take into consideration utilizing one before you begin. Opportunities are you may need a specialist plumber to make tube connections.
This short article will assist you set up a new bathtub in your restroom if you have currently gotten a new bathtub as well as don't need to transform the plan of your previous water system pipelines.
Your devices as well as product list ought to consist of the following:
Planning for the Installment
Firstly, the supporting frame supplied with the bathroom needs to be fitted (if called for) according to the supplier's directions. Next off, fit the taps or mixer to the tub. When fitting the tap block, it is necessary to ensure that if the faucet features a plastic washer, it is fitted between the bathroom and also the taps. On a plastic bathroom, it is also reasonable to fit a supporting plate under the faucets device to stop strain on the bathtub.
Fit the flexible faucet adapters to the bottom of both faucets making use of 2 nuts as well as olives (occasionally provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and after that pass the outlet via the hole in the bathroom. Utilize the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bath. Make certain you use every one of the supplied washing machines.
Connect the trap to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Link all-time low of the overflow tube in a comparable manner.The bath ought to now be ready to be fitted in its final setting.
Removing Old Touches
If you require to change old faucets with brand-new ones as a part of your installment, after that the first thing you should do is detach the supply of water. After doing so, turn on the taps to drain pipes any kind of water remaining in the system. The procedure of eliminating the existing faucets can be fairly bothersome as a result of the limited accessibility that is often the situation.
Use a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that attaches the supply pipes to the faucets. Have a towel ready for the staying water that will originate from the pipes. Once the supply pipelines have actually been eliminated, make use of the exact same tool to loosen the nut that holds the taps onto the bath/basin. You will need to quit the solitary faucets from turning during this procedure. Once the taps have been removed, the holes in the bath/basin will need to be cleaned up of any type of old securing compound.
Before going on to fit the new taps, contrast the pipe links on the old taps to the new faucets. If the old faucets are longer than the new taps, after that a shank adapter is required for the new taps to fit.
Mounting the Bathtub
Using both wood boards under its feet, place the bathtub in the needed placement. The wood boards are helpful in uniformly spreading out the weight of the bathtub over the area of the boards instead of concentrating all the weight onto four little factors.
The following objective is to make sure that the tub is leveled all round. This can be attained by examining the spirit level as well as changing the feet on the tub up until the spirit level checks out degree.
To set up faucets, fit the bottom of the furthest adaptable tap port to the appropriate supply pipe by making a compression join; after that do the very same for the various other tap.
Activate the supply of water and also check all joints as well as new pipework for leaks and tighten them if needed. Fill up the bathtub and also examine the overflow electrical outlet and also the regular outlet for leakages.
Lastly, fix the bath paneling as defined in the manufacturer's user's manual. Tiling and securing around the bath tub ought to wait up until the bath tub has been made use of a minimum of when as this will resolve it into its last setting.
Suitable New Taps
If the tails of the new taps are plastic, then you will certainly need a plastic connector to prevent damages to the thread. One end of the port fits on the plastic tail of the tap as well as the various other end gives a link to the existing supply pipes.
If you require to fit a monobloc, then you will certainly need lowering couplers, which connects the 10mm pipe of the monobloc to the standard 15mm supply pipe.
Next, place the tap in the mounting hole in the bath/basin making certain that the washing machines remain in location between the faucet and also the sink. Safeguard the tap in place with the maker supplied backnut. Once the tap is safely in place, the supply pipes can be connected to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with typical tap connectors. The former type needs to be connected to the faucet finishes first, tightening only by hand. The supply pipelines can later be connected to the various other end. Tighten both ends with a spanner after both ends have been attached.
Tiling Around the Tub
In the area where the bathroom satisfies the floor tile, it is necessary to secure the accompanies a silicone rubber caulking. This is necessary as the installation can relocate enough to split a stiff seal, triggering the water to permeate the wall in between the bathroom and the tiling, resulting in problems with moisture and also feasible leaks to the ceiling below.
You can select from a selection of coloured sealers to blend in your fixtures as well as installations. They are sold in tubes and also cartridges, as well as are capable of sealing voids approximately a size of 3mm (1/8 inch). If you have a bigger space to fill, you can fill it with twists of drenched paper or soft rope. Keep in mind to always fill the bath tub with water before securing, to permit the activity experienced when the tub is in usage. The sealer can split fairly very early if you do not take into account this activity prior to sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are likewise quickly readily available on the market. It is suggested to fit the ceramic tiles using waterproof or waterproof sticky as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you appreciate more info about How to Install a Bathtub? Try to leave feedback below. We would be pleased to find out your views about this piece. In hopes that you come back again before long. Enjoyed our article? Please share it. Help somebody else locate it. Thank-you for taking the time to read it.
Schedule Services Report this page